ABB PVS300 Manual Pagina 103
- Pagina / 130
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Troubleshooting 103
16 Ground Current The inverter’s RCMU has diagnosed leakage current to ground
during the inverter’s power feeding operation and has
disconnected itself from the electrical grid. Leakage current can be
the result of human, animal or another object’s contact between
(faulty) cabling or electrical device and ground. Leakage current
can also be caused by water ingress or high humidity at the PV
modules or junction boxes creating current path to ground.
Power down the inverter.
Check that no people, animals or other objects are in danger or in
contact with electrical parts of your PV system.
Check visually that there are no faults or burn marks around the
cabling of your PV system.
If the system looks normal then try to restart the inverter.
If the inverter returns to ‘Ground fault state’, immediately isolate
the inverter from all power sources.
Request a service visit from your system supplier. Your PV system
might have a dangerous AC or DC side isolation fault and contact
to ground.
17 Ground
impedance
The inverter has diagnosed too low impedance (isolation fault)
between the DC+ or DC
-
bus of the inverter and ground before
establishing grid connection.
Low impedance can be the result of faulty DC cabling between
device and ground. Low impedance can also be caused by water
ingress or high humidity at PV modules or junction boxes creating
a current path to ground.
Power down the inverter.
Check visually that there are no faults or burn marks around the
cabling of your PV system.
If the system looks normal then try to restart the inverter.
If the inverter returns to ‘Ground fault state’, immediately isolate
the inverter from all power sources.
Request a service visit from your system supplier. Your PV system
might have a dangerous DC side isolation fault and contact to
ground.
18 RCD Sensor Fault detected in the residual current monitoring unit.
Power down the inverter.
Restart the inverter.
If the inverter returns to ‘RCD Sensor’, immediately isolate the
inverter from all power sources and contact your system supplier.
21 Current
measurement
The inverter has diagnosed an error in current measurement.
Try to reset the fault and monitor if the inverter returns to normal
operation or not.
If the inverter does not return to normal operation, power down the
inverter and contact your system supplier.
Fault
message
ID code
Fault message
description
Causes of fault and corrective actions
- Product manual 1
- PVS300 string inverters 1
- List of related manuals 2
- Table of contents 5
- 4. Planning the installation 6
- 5. Mechanical installation 6
- 6. Electrical installation 6
- 7. Installation checklist 7
- 8. Start-up 7
- 9. Operation 7
- 8 Table of contents 8
- 10 Table of contents 10
- What this chapter contains 11
- Use of warnings 11
- 12 Safety 12
- Intended use 13
- Grounding safety (PE) 14
- Safe start-up and operation 15
- General safety 16
- Introduction to the manual 17
- Related documents 18
- Terms and abbreviations 21
- Operation basics and 23
- Layout drawing 25
- PVS300 block diagram 28
- Features 29
- Type designation label 31
- Type designation key 31
- Optional accessories 32
- RJ45 data connector X6 33
- Additional PE terminal 33
- Planning the installation 35
- Selecting the power cables 37
- Selecting the control cables 39
- General tools 41
- The use of external RCD 43
- Mechanical installation 49
- 52 Mechanical installation 52
- Installation sequence 54
- Electrical installation 57
- Routing the cables 58
- Inverter 59
- AC output cable 59
- Solar generator 59
- Connection diagram 60
- Connecting the power cables 61
- 62 Electrical installation 62
- Electrical installation 63 63
- 64 Electrical installation 64
- Electrical installation 65 65
- Connecting the control cables 66
- Output relay, terminal X1 68
- 70 Electrical installation 70
- Electrical installation 71 71
- Connection procedure 72
- Installation checklist 73
- 74 Installation checklist 74
- Installation checklist 75 75
- 76 Installation checklist 76
- Start-up 77
- 78 Start-up 78
- Start-up 79 79
- 80 Start-up 80
- Start-up 81 81
- 82 Start-up 82
- Operation 83
- Operation 85 85
- Control buttons 86
- LED indicators 87
- LED on control unit 88
- Graphical display 89
- Common display zones 90
- Start up assistant 91
- Output view menu 91
- Special screens 94
- Messages 94
- Progress indication 94
- Maintenance 95
- Replacing fans 97
- Available spare part kits 98
- Troubleshooting 99
- Replacing the inverter 101
- Fault messages 101
- 102 Troubleshooting 102
- Troubleshooting 103 103
- 104 Troubleshooting 104
- Troubleshooting 105 105
- 106 Troubleshooting 106
- Warning messages 107
- 108 Troubleshooting 108
- Troubleshooting 109 109
- 110 Troubleshooting 110
- Decommissioning 111
- Recycling 112
- Technical data 113
- 114 Technical data 114
- Technical data 115 115
- Mechanical data 116
- Performance data 116
- MPPT adjustment efficiency 117
- Conversion efficiency 117
- 118 Technical data 118
- Product compliance 119
- Derating 119
- 120 Technical data 120
- Dimension drawing 121
- 122 Dimension drawing 122
- Dimension drawing 123 123
- 124 Dimension drawing 124
- Navigation map 125
- The navigation map 126
- Navigation map 127 127
- 128 Navigation map 128
- Further information 129
- Contact us 130
LG LFX29945ST manuales
Manuales del propietario y guías del usuario para No LG LFX29945ST.
Ofrecemos 1 manuales en pdf LG LFX29945ST para descargar gratis por tipos de documentos: Guia Energética
Comentarios a estos manuales